PENGARUH VARIASI WAKTU SPHEROIDIZING ANNEALING TERHADAP STRUKTUR MIKRO DAN SIFAT MEKANIK BAJA PADUAN Fe-14,8Mn-11,9Al-0,7C
Abstrak
Fe-Mn-Al-C alloy steel is a new austenitic stainless steel candidate alloy, where Al and Mn elements replace Cr and Ni elements. After casting alloy steel Fe-14.8 Mn-11.9 Al-0.7 C turned out to have a hardness of up to 42 HRC and difficult to machining. This study specifically aims to further investigate the effect of spheroidizing annealing process on alloy steel Fe-14.8 Mn-11.9 Al-0.7 C by varying the annealing time to increase tensile strength, microstructure stability, and decrease the hardness value. Ingot sheets are formed into several specimens and then annealed at a temperature of 1100 ° with time variations of 45, 60, and 90 minutes. The specimens were tested for chemical composition, microstructure analysis, and mechanical properties. In the microstructure of raw materials obtained Ferrite and austenite phases, based on the results of microstructure photos at the time variations found no new phase and no significant difference, visible ferrite structure becomes larger / more elongated and austenite structure is shrinking. Hardness test results using the highest Vickers method in raw materials amounted to 463.6 kg / mm2 after the annealing process hardness value decreased but not significantly, because after peroses annealing ferrite structure obtained that looks bigger. The results of tensile strength testing of raw materials amounted to 343.58 MPa and obtained the highest stress in the variation time 45 minutes of 422.18 Mpa, or increased by 22.8%.
Referensi
Kalashnikov, I. S. et al. (2000) ‘Behavior of Fe-Mn-Al-C steels during cyclic tests’, Journal of Materials Engineering and Performance, 9(3), pp. 334–337. doi: 10.1361/105994900770346015.
Yuan, X., Yao, Y. and Chen, L. (2014) ‘High-temperature oxidation behavior of a high manganese austenitic steel Fe-25Mn-3Cr-3Al-0.3C-0.01N’, Acta Metallurgica Sinica (English Letters), 27(3), pp. 401–406. doi: 10.1007/s40195-014-0071-1.
Hwang, S. W. et al. (2011) ‘Tensile deformation of a duplex Fe-20Mn-9Al-0.6C steel having the reduced specific weight’, Materials Science and Engineering A, 528(15), pp. 5196–5203. doi: 10.1016/j.msea.2011.03.045.
Yin, Y. jun et al. (2018) ‘Ultra-low-carbon steel spheroidization and torsion’, Journal of Iron and Steel Research International, 25(9), pp. 968–974. doi: 10.1007/s42243-018-0137-9.
Ambiyar., & Purwantono. (2008). Fabrikasi Logam. Padang: UNP Press Padang.
Rabinkin, A. (2011). The pure manganese end member of this Fe-Mn phase diagram shows the higher temperature Mn phases. The image appears on a website entitled, "Iron-Manganese (Fe-Mn) Phase Diagram" at url=http://www.calphad.com/iron-manganese.html.
Maulana, Andi., Kartikasari, R., & Setyo Pamuji, Didit. (2022). Pengaruh waktu proses Deep Cryogenic Treatment – Temper terhadap struktur mikro, kekerasan, dan kekuatan paduan Fe-14Al-21,3Mn
Y. T. Zhang, X. Y. Li, D. Z. Li, et al. (2008). PHASE DIAGRAM CALCULATION AND EXPERIMENT FOR FEMN-AL SYSTEM AT DIFFERENT TEMPERATURE. China
Maitano, A. F. D., Kartikasari, R., & Muhfidin, R. (2022). Pengaruh Waktu Proses Deep Cryogenic Treatment Terhadap Struktur Mikro, Kekerasan, dan Keausan Paduan Fe-Al-Mn-Mo. ReTII, 56-61.
This journal provides immediate open access to its content on the principle that making research freely available to the public supports a greater global exchange of knowledge.
All articles published Open Access will be immediately and permanently free for everyone to read and download. We are continuously working with our author communities to select the best choice of license options, currently being defined for this journal as follows:
• Creative Commons Attribution-ShareAlike (CC BY-SA)
